Integra® Manual Valves, 1/4" Orifice, 2-way, Multi-turn
To discuss your specific needs, contact your local Entegris representative.
Don't have an Entegris representative?
Contact UsThank you for requesting a quote. Someone from Entegris will contact you shortly.
Your quote number is {0}.
Ideal in point-of-use applications when low flow is required, including:
- High-purity, corrosive chemical handling
- Wet etch and clean (WEC) process chemicals
- Low volume bulk chemical delivery
- Chemical line sizes 1/2" or smaller
Specifications
Dimension Note:
Dimensions are the same regardless of body material (PVDF or ECTFE) or nut material (PVDF, PFA or CPFA).
Port Connection | Flow Factor Cv (Kv) | Dimensions | |||
A | B | C (Closed) | D (Open) | ||
1/4" Flaretek | 0.24 (3.4) | 3.12" (79.2 mm) | 0.49" (12.4 mm) | 4.45" (113.0 mm) | 4.76" (120.9 mm) |
1/4" PureBond fusible pipe | 0.75 (11.0) | 4.00" (101.6 mm) | 0.57" (14.5 mm) | 4.53" (115.1 mm) | 4.84" (122.9 mm) |
1/4" FNPT | 0.75 (11.0) | 2.75" (69.8 mm) | 0.57" (14.5 mm) | 4.53" (115.1 mm) | 4.84" (122.9 mm) |
3/8" Flaretek | 0.75 (11.0) | 4.64" (117.9 mm) | 0.57" (14.5 mm) | 4.53" (115.1 mm) | 4.84" (122.9 mm) |
1/2" Flaretek | 0.75 (11.0) | 4.64" (117.9 mm) | 0.57" (14.5 mm) | 4.53" (115.1 mm) | 4.84" (122.9 mm) |
Panel Mount Instructions
- Panel thickness must be within 0.12" (3.0 mm) to 0.38" (9.6 mm).
- To panel mount, the handle must be removed. Place the valve fully in the closed position and remove the screw holding the handle in place.
- Remove the handle taking care not to disturb the position of the red indicator.
- To install the valve, remove the panel mount nut and insert valve into the panel.
- Thread the panel mount nut onto the valve. Again take care not to disturb the red indicator position.
- Place the handle on the valve, lining up the screw holes. Install the screws.
- After installing on panel, thread the panel mount nut to 40 inch•lbs (4.5 N•m) torque, or 1/8-turn beyond hand tight.
Note: The Inlet Pressure vs. Outlet Pressure as a Function of Media Temperature graph is not applicable for valves with ECTFE external components. For ECTFE temperature rating refer to the Specification table below.
Pressure range: | 29" Hg vacuum (980 mbar) to 100 psig (689.5 kPa) |
Temperature range: | 75° to 150°F (24° to 65°C), ambient 75° to 300°F (24° to 150°C), fluid 35° to 75°F (2° to 24°C) for ECTFE external components, ambient and fluid |
Materials: | All wetted parts are PFA. Exterior actuator parts are PVDF. Interior actuator parts are PVDF, stainless steel and Viton®. |
Note: Actual valve performance varies with pressure and temperature. Refer to actual ratings in performance charts.
CAUTION!
The valve port-to-port seal travel adjustment nut is set at the factory. DO NOT move the adjustment nut on the valve. If altered in the field, use the following procedure to properly reset the nut.
- Close the valve and connect 80 psig (551.6 kPa) air pressure to the outlet port.
- Remove the two white screws and remove the handle.
- Back off the red adjustment nut.
- Put the handle back on and tighten until the leak stops. Tighten an additional ¼ turn.
- Remove the handle taking care not to disturb the red indicator position.
- Thread red adjustment nut until it stops, then back off the red adjustment nut to match hexes. Replace the handle.
- Replace the two screws.
Successfully Opted for software Updates
-
I4-MB-01
Mounting base for use with 1/4" 2-way Integra® valves except valves with 1/4" Flaretek® port connections
-
213-102-01
Tool kit for 1/4" Integra® 2-way or sampling valves.
Part Number | Inlet | Outlet | Options |
---|---|---|---|
201-81-01 | 1/2" Flaretek® | 1/2" Flaretek® | PVDF Flaretek® nut |
201-81-01-3 | 1/2" Flaretek® | 1/2" Flaretek® | PFA Flaretek® nut |
201-85-01 | 1/4" PureBond® pipe | 1/4" PureBond® pipe | N/A |
201-85-01-EC | 1/4" PureBond® pipe | 1/4" PureBond® pipe | ECTFE actuator |
201-87-01 | 3/8" Flaretek® | 3/8" Flaretek® | PVDF Flaretek® nut |
201-87-01-3 | 3/8" Flaretek® | 3/8" Flaretek® | PFA Flaretek® nut |
201-92-01-EC | 1/4" FNPT | 1/4" FNPT | ECTFE actuator |
201-97-01 | 1/4" Flaretek® | 1/4" Flaretek® | PVDF Flaretek® nut |
201-97-01-3 | 1/4" Flaretek® | 1/4" Flaretek® | PFA Flaretek® nut |
201-97-01-EC | 1/4" Flaretek® | 1/4" Flaretek® | ECTFE actuator with PFA nut |